Fujian Southchina Heavy Machinery Manufacture Co.,Ltd

Catalogue

Contact US

Address: Road, Taiwanese Investment Area, Quanzhou, Fujian, China

MOB: +86 18859225922

FAX: +86-592-5650876

Email: john@socmachinery.com

          jackson@socmachinery.com

         sunny@socmachinery.com

Website: www.socma-forklift.com

25 Ton Forklift

25 Ton Forklift

HNF-250 Rated load: 25,000 kgs
Load center: 900 mm
Operating weight: 35,000 kgs
Wheel base: 4,000 mm
1, rear axle by transverse hydraulic cylinder type steering, steering axle has compact structure, transmission angle is 70.5 °, help to reduce the resistance and reduce tire wear and improve the...

Chat Now

    HNF-250

    Rated load: 25,000 kgs

    Load center: 900 mm 

    Operating weight: 35,000 kgs 

    Wheel base: 4,000 mm

    1, rear axle by transverse hydraulic cylinder type steering, steering axle has compact structure, transmission angle is 70.5 °, help to reduce the resistance and reduce tire wear and improve the driving comfort.

    2, front axle adopt heavy duty type driving axle, enlarge size of axle housing, hub and bearing, spiral bevel gear and wheel planetary wheel deceleration increasing twist, steel structure bridge shell support, increase the load capacity and service life.

    3, cooperate with hercynian institute of Chinese Academy of Sciences "overall structure optimization scheme", verifies the stiffness and strength calculation, fatigue life forecast on the forklift, comprehensive finite element mechanics analysis, structure design optimization, ensure the security of the products use 

    4, Variable speed control valve matched with neutral starter, the machine start more secure.
    5, No spokes plate type rim, increase the bearing capacity of hub.
    25 Ton Forklift

    25 Ton Forklift

    25 Ton Forklift

    25 Ton Forklift

    25 Ton Forklift


    How to operate 25 Ton Forklift 

    (C) stable driving

    (1) when driving, the bottom of fork leaves ground height should be maintained 300-400mm, mast to be tilted.

    (2)Don’t raise the fork too high when driving. Access to the job site or on the way, we should pay attention to whether there are obstacles across the scratch. When the load is running, if the fork lifts too high, it will increase the overall weight of the 25 Ton Forklift height and affecting the stability of the forklift.

    (3) after unloading, should first drop the fork to the normal driving position and then travel.

    (4) When turning, if there are pedestrians or vehicles nearby, a signal should be signaled and high-speed turn is prohibited. High speed sharp turns will cause the vehicle to lose lateral stability and tipping.

    (5) 25 Ton Forklift cargo downhill, should be backwards to prevent the goods fall.

    (6) 25 Ton Forklift in operation to comply with provisions of the factory traffic rules, must be in front of the vehicle to maintain a certain safe distance. Non-special circumstances, prohibit the movement of vehicles in the brakes.

    (7) When the vehicle is running up and down, the brake may not be used without non-special circumstances.

    (8) without non-special circumstances, It is forbidden to carry the brakes when vehicle movement .

    (9) 25 Ton Forklift from the rear wheel control steering, it must always pay attention to the post-car swing, to avoid beginners driving often appear sharp turn urgent phenomenon.

    (10) internal combustion forklift turning on the ramp, should not travel across the ramp.

    (11) It is forbidden to turn on a ramp and not to travel across a ramp.

    (12) When the forklift is running, the load must be at the lowest position without obstruction, and the gantry should be properly tilted, and the load shall not be increased during stacking or loading. In the handling of large objects, the object block the driver's line of sight, this time should be to forklift.

    (13) forklifts in and out of the workshop, turning, reversing and crossing must be horn, to prevent accidents.

    (D) safe handling

    (1) When the goods are taken with the fork, the fork shall be carried out as far as possible under the load, and the cargo fork can not be touched against other goods or objects. The minimum gantry should be used to stabilize the load to avoid sliding the load backwards. When the load is released, the mast can be tilted in a small amount to accommodate the load and the fork.

    (2) the height of the load shall not obscure the driver's sight.

    (3) During the loading and unloading of items, the brake must be used to brake the forklift.

    (4) fork close to or withdrawal of goods, the speed should be slow and steady, pay attention to the wheels do not rolling items, wooden mats, so as not to fall from the injury.

    (5) when forked items, should be adjusted on the two fork spacing, so that the two fork load balance, not skewed, one side of the items should be attached to the shelves, fork load weight should meet the requirements of the load center curve signs.

    (6) prohibit high-speed fork to take the goods and use fork collide with hard objects.

    (7)25 Ton Forklift operation, prohibit manned driving.

    (8)25 Ton Forklift operation, prohibit people standing around the fork, so as to avoid the collapse of the goods hurt.

    (9) prohibit the use of fork lift personnel engaged in high operations, so as to avoid a high fall accident.

    (10)not allowed to use the inertia of the brake items.

    (11) When the forklift is operated, it is forbidden to stand on the fork.

    (E) the end of work to get off work

    (1) 25 Ton Forklift need to wipe clean, keep the appearance clean and oil-free.

    (2) After use forklift, the forklift fork to the front of the fork to the ground, so as not to cause harm to people.

    (3) after parking, need to tighten the handbrake, to prevent the slide

     

    Parameter of 25 Ton Forklift

    Item

    Item details

    Unit


    HNF-250

    Features

    Rated Load

    Q(t)

    25

    Load center

    c(mm)

    1250

    Wheelbase

    y(mm)

    4400

    Weight

    Weight

    kg

    35000

    Chassis

    Tyre Specs.:Front


    14.00-24-28PR

    Tyre Specs.:Rear


    14.00-24-28PR

    Tyres Qty,front/rear(X-drive wheels)


    4\2

    Wheel tread:Front

    b10(mm)

    2200

    Wheel tread:Rear

    b11(mm)

    2390

    Dimension

    Mast/carriage tilt angle(front/rear)

    Degree(°)

    6\12

    Mast height(fork lowering)

    h1(mm)

    3860

    Mast lifting height

    h3(mm)

    3500

    Max.lifting height

    h4(mm)

    5610

    Height to head guard(height to cab)

    h6(mm)

    3510

    Overall height(with forks)

    l1(mm)

    9190

    Fork front vertical surface to the rear end of the vehicle

    l2(mm)

    6745

    Overall width

    b1/b2(mm)

    3050

    Fork dimension

    s/e(mm)

    2440X300X110

    Fork carriage width

    b3(mm)

    3060

    Mast min ground clearance(with load)

    m1(mm)

    300

    Wheelbase center min ground clearance(with load)

    m2(mm)

    420

    Min.Turning radius

    Wa(mm)

    6700

    Travel speed(with load/without load)

    km/h

    25/29

    Performance

    Max.lifting speed    (with load/without load)

    mm/s

    260/270

    Max.Lowering speed     (with load/without load)

    mm/s

    315/260

    Traction

    N

    17000

    Gradeablity(with load/without load)

    20/21

    Driving brake


    Hydraulic clamp disc


    Engine brand/model

    Optional one

    Weichai engine

    Engine


    WP10G220E343
    9.726L 162KW 2000rpm

    Optional two

    Dongfeng Cummins


    QSC8.3-C240
    8.3L 179KW 2200rpm

    Cylinder No.

    6

    Others

    Transmission gears(Front/rear)


    2\1

    Attachments working pressure

    bar

    180

    Attachments using oil amount

    l/min

    80



Hot Tags: 25 ton forklift, China, manufacturers, factory, customized
Related Products
Inquiry